What is Lapping ?(2)

2022-05-24 13:35:37 21

What is Lapping?

The principle of lapping is simple and based on the grinding power of a free grain in an emulsion. A lapping plate on which a lapping emulsion has been applied moves under the workpiece surface. Although it seems as if the abrasive grains are working in a free movement, this is not entirely true. Part of the grains settle in the structure of the lapping plate. Due to the movement of the lapping plate in relation to the workpiece, you slowly remove material. Lapping can produce dull grey semi-reflective finished depending on the material being lapped, and the method of lapping. Lapping is a precision operation. So it takes quite a bit of time. To speed up the process, it is best to work in several steps from a coarse to a fine process. You do this by gradually switching from a relatively large grit on a hard lapping plate to a fine grit on a soft composite plate or polishing cloth.



Why do we need to Lap?

  • To produce a fine surface finish

  • To produce sealing surfaces

  • To produce sharp cutting edges

  • To produce flat stress free surfaces

  • To produce a datum face

  • To improve the wear resistant properties of surfaces


What is Polishing?

Polishing is often carried out after a lapping operation, to produce the ultimate in surface finish. Some of the common reasons for polishing are:-

  • To produce mirror surfaces

  • To improve appearances

  • To obtain the optimum sealing surfaces

  • To optically measure flatness

  • To improve electrical contact

  • To improve the optical qualities of materials


What is Conventional Lapping?

Conventional lapping ensures a relatively high stock removal. The abrasive (aluminium oxide or silicon carbide) is applied in a carrying vehicle (Lapping Oil) onto a hard surface such as cast iron. The particles cannot be pressed into the surface and be secured there, so they roll and move freely in all directions. They hammer small particles out of the sample surface, introducing deep deformations. This takes place because the free moving abrasive particle is not able to produce a real "chip" of the component surface.


What is Diamond Lapping?

Diamond lapping is a material removal method using fixed diamond abrasive particles which produce chips of the component material. The process of making chips with a sharp abrasive grain produces the lowest amount of deformation in the component while giving the highest removal rate.

Diamond abrasive is pushed into the lapping plate surface, by a chamfer on the leading edge of the conditioning rings.

A reflective or (high) glossy result can be obtained by lapping on a composite lapping plate with a diamond emulsion. A finer grit size results in a lower roughness value.


What is Diamond Polishing?

Diamond Polishing uses the same mechanism as Diamond lapping. However by using successively small grain sizes of 8, 6 and 3 micron diamond, with softer Kemet plates and polishing pads with higher resilience, polishing can remove the deformations and scratches from lapping.


What is Lubrication?

Sufficient lubrication between sample surface and the grinding/polishing surface is necessary because:

  • Enhancement of cutting: The correct lubricant improves the cutting process and yields the smallest scratch depth and lowest deformation

  • Reduce friction: The friction between the sample and the support must be correct; too little lubricant will cause over heating, too much lubricant will decrease the cutting action by washing away abrasive particles and creating aqua-planing condition.

  • Cooling: The ideal conditions for optimal lapping/polishing will create frictional heat. This is kept low by using the correct lubricant

Why Choose Kemet Lapping Systems?

GRISH Lapping and Polishing Systems offer the most efficient and reliable method of producing precision flat polished surfaces. Our flat lapping and polishing machines, and systems, are at the forefront of today's advanced lapping technology, especially when used with GRISH Diamond products.

GRISH Diamond quality and grading enables reliable precision lapping to be performed in production situations. Each GRISH Diamond product is a special blend of diamond powder with a specific grading and concentration in a chemical carrier to give optimum stock removal and surface finish, ease of cleaning, temperature resistance and lubricity to prevent drying out.

GRISH Diamond lapping generates less waste and is considered more environmentally friendly than conventional lapping methods.

Which Applications use GRISH Lapping Systems?

The range of industries using GRISH Lapping systems is wide and varied:


AerospacePumps & ValvesTechnical CeramicsTool and Die
Pumps & ValvesFuel PumpsAlumina - ZirconiaMould and Inserts
Turbine PartsHydraulic PumpsSilicon CarbidePrinting Plates
Engine AssembliesMechanical SealsPiezo CeramicsSlitter Knives
SpacersGate ValvesFerriteExtrusion Dies
Medical DevicesData StorageElectro opticsAutomotive
Fibre ScopesDisc Drive HeadsPlano OpticsDiesel Injectors
Surgical InstrumentsTape HeadsLaser Rods and PrismsPiston Rings
Pacemaker PartsCD MouldsFibre OpticsFuel Pumps


Sensors


Tel
Products
Applications
Sample Apply
Polishing Machine